film capacitors ? power factor correction current limitation reactor series/type: bd-100 ordering code: B44066T0100E400 date: march 2010 version: 1 ? epcos ag 2010. reproduction, publicati on and dissemination of this publicatio n, enclosures hereto and the information contained therein without epcos' pr ior express consent is prohibited. entered in headers and footers! please fill in the don't change formatting when entering or pasting text in the table and don't add any cell or line in and to it! identification/classification 1 (header 1 + top left bar): film capacitors ? power factor correction identification/classification 2 (header 2 + bottom left header bar): current limitation reactor ordering code: (top right header bar) B44066T0100E400 series/type: (top right header bar) bd-100 preliminary data (optional): (if necessary) department: film pc pm pfc date: march 2010 version: 1
film capacitors ? power f actor correction B44066T0100E400 current limitation reactor bd-100 film pc pm pfc please read cautions and warnings and page 2 of 4 important notes at the end of this document . characteristics ? single phase current limitation react or for thyristor modules tsm-series in conventional pfc-systems without reactor ? protection of thyristor modules series tsm-lc10, tsm-lc25 and tsm-lc50 (two units per step required). technical data dimensions 75 90 75 mm (w h d) weight 2 kg nominal voltage max. 440 v nominal current 85 a (50 hz) frequency 50/60 hz linearity 120 a mode of operation continuous operation inductivity l = 0.1 mh specification en61558-2-20 maximum operating ambient temperature 80 c
film capacitors ? power f actor correction B44066T0100E400 current limitation reactor bd-100 film pc pm pfc please read cautions and warnings and page 3 of 4 important notes at the end of this document . cautions and warnings ? the bd-100 is designed exclusively for use in dynamic lv-pfc-systems without detuning reactors. ? not suitable for tsm-lc 100, tsm-lc 200 and tsm-hv 200!. ? the maximum permissible nominal voltage (see technical data) must not be exceeded! ? the equipment may be operated only by suitably trained personnel. ? a minimum distance of 50 mm towards the adjoining component set has to be kept. ? mounting onto mounting plate. ? mounting position random. ? connection 2-pole via busbar; cable lug 25 mm 2 note for detailed information about pfc capacitors and cautions, refer to the latest version of the epcos pfc product profile.
important notes page 4 of 4 the following applies to all products named in this publication: 1. some parts of this publication contain statements about the suitability of our products for certain areas of application . these statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. we nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. as a rule, epcos is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. for these reasons , it is always ultimately incumbent on the customer to check and decide whether an epcos product with the properties described in the product specification is suitable for use in a particular customer application. 2. we also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. in customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must theref ore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. the warnings, cautions and product-specific notes must be observed. 4. in order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous) . useful information on this will be found in our material data sheets on the internet (www.epcos.com/material). should you have any more detailed questions, please contact our sales offices. 5. we constantly strive to improve our products. consequently, the products described in this publication may change from time to time . the same is true of the corresponding product specifications. please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. we also reserve the right to discontinue production and delivery of products . consequently, we cannot guarantee that all products named in this publication will always be available. the aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. unless otherwise agreed in individual contracts, all orders are subject to the current version of the ?general terms of delivery for products and services in the electrical industry? published by the german electrical and electronics industry association (zvei) . 7. the trade names epcos, baoke, alu-x, ceradiode, csmp, cssp, ctvs, deltacap, digisimic, dssp, miniblue, minicell, mkk, mlsc, motorcap, pcc, phasecap, phasecube, phasemod, phicap, siferrit, sifi, sikorel, silvercap, simdad, simic, simid, sineformer, siov, sip5d, sip5k, thermofuse, windcap are trademarks registered or pending in europe and in other countries. further information will be found on the internet at www.epcos.com/trademarks.
|
